Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to FTABeta.com

We're a new community open to help you with any FTA Issues that you may be experiencing, feel free to ask any questions, and enjoy! You may have to register before you can post: register

x
Results 1 to 6 of 6
  1. #1

    Default Failed to read Configuration File

    I keep getting this message when I start the rq-sssp.exe this is my conf:
    ################################################## #############################
    # #
    # rq-sssp-client configuration file #
    # All configuration options in this file observe the same format: #
    # <configuration_name>=<configuration_value> #
    # #
    ################################################## #############################
    # #
    # THIS CONFIGURATION FILE HAS BEEN MODIFIED FOR CAPTIVEWORKS and NFPS #
    # #
    ################################################## #############################
    # #
    # IF YOUR SERIAL COM PORT IS OTHER THEN 1 YOU WILL NEED TO CHANGE IT #
    # #
    ########################### general configuration #############################
    [General]
    # Serial port where the client receiver is connected.
    # Examples:
    # Linux PC: /dev/ttyS0, /dev/ttyS1, ... /dev/ttyS<n>
    # Dreambox/TD/DGS: /dev/tts/0, /dev/tts/1, ... /dev/tts/<n>
    # Windows: COM1, COM2, ... COM<n>
    serial_port=COM3
    # Serial port communication settings.
    # Example: 115200|8|N|1 = 115200bps, 8 data bis, no parity, 1 stop bit.
    serial_port_settings=115200|8|N|1
    # Sets the byte write delay. The default value of this parameter is 200us
    # which should work for most receivers. You can tweak this value in case
    # you're having communication problems. Sensible values for this parameter
    # go from 0 to 500 (microseconds).
    #
    # NOTE: This parameter *has no effect* in the Dreambox versions (PPC and MIPS).
    byte_write_delay=200
    # SSSP protocol variant
    # 0 - Captiveworks SSSP Protocol (Captiveworks receivers)
    # 1 - Coolsat SSSP Protocol (Coolsat receivers)
    # 2 - Gbox SSSP Protocol (Digiwave, Technomate and many other EU receivers)
    receiver_protocol=0
    # CaID mappings. This is used to solve CaID mismatch errors when a
    # receiver reports the wrong CaID (this can happen when the provider uses
    # multiple CaIDs). If you're sure the card server you're using supports the
    # provider, you can override the CaID mismatch check this way.
    #
    # Format:
    # caid_mappings=<original_caid>:<mapped_caid>|<origi nal_caid>:<mapped_caid>| ...
    #
    # Example: Your receiver may report CaID 1802, the card server
    # reports CaID 1816. Add this mapping:
    #
    # caid_mappings=1802:1816
    #
    # You can also add several mappings like this:
    #
    # caid_mappings=1802:1816|1803:1816| ...
    caid_mappings=
    # If enabled either the even or odd control word is returned for each
    # ECM. The single control word is duplicated. This is intended as a fix
    # for freezing on some receivers when using NDS providers.
    # 0 - Disabled
    # 1 - Return Even on 0x80 ECM table id, Odd on 0x81 ECM table id
    # 2 - Return Odd on 0x80 ECM table id, Even on 0x81 ECM table id
    # 3 - Always return Even
    # 4 - Always return Odd
    return_single_cw=0
    # Enable or disable background execution
    # 0 - Disable
    # 1 - Enable
    #
    # NOTE: Ignored in the WIN32 version.
    background_execution=1
    # This sets the level of console output for debugging:
    # 0 - Silent, 1 - Basic debug info, 2 - Extended debug info,
    # 3 - Show all debug info
    debug_level=2
    # This option enables or disables the writing of debug information to the
    # console.
    log_to_console=1
    # This option enables or disables the writing of console output to a log file
    log_to_file=0
    # When log_to_file is set to 1, this is the path and filename to write console
    # ouput to.
    #
    # NOTE: In the WIN32 version, if enabled, this should be set to a valid
    # Windows/DOS path.
    logfile_name=/var/bin/rq-sssp-client.log
    # Timeout in seconds for receiving control words from server.
    # Default value is 12 seconds
    control_words_timeout=25
    ################################################## ###############################################
    # #
    ########### CHANGE THE FOLLOWING IN card_server_url line THE LAST LINE OF THIS FILE ###########
    # #
    ################################################## ###############################################
    # #
    # replace twice YOURACCESSCODE with your actual 14 digit access code #
    # #
    # change the PORT# REPLACE ##### with your PORT# #
    # use the following information to determine your correct port number #
    # #
    # Clients with donation numbers that start with 010, 110, 210 and nfps210 change the port to #
    # #
    # starting with 010 --->use ports 11010 and/or 12010 #
    # starting with 110 --->use ports 11110 and/or 12110 #
    # starting with 210 and nfps210 --->use ports 11210 and/or 12210 #
    # #
    # Clients whose donation numbers DO NOT START WITH 010, 110, 210 or nfps210 change the port to #
    # #
    # 10410 and/or 10510 #
    # #
    # The above does not apply to recent donations where you were instructed to use #
    # Port numbers 10610 and/or 10710 you should continue to use those port numbers #
    # #
    # NOTE Before saving place your cursor at the end of the newcamd line immediately after the 4 #
    # now hit the right arrow key on your keyboard and the cursor should drop to the left hand #
    # position of the next line - if it does not with the cursor after the 4 hit the return key #
    # once the cursor should go to the left hand side of the next line - Save file as instructed #
    ################################################## ###############################################
    #
    # URL of card-server to use, formats are as follows:
    #
    # newcamd://<username>:<password>@<hostname>:<port>/<des_key>
    #
    card_server_url_1=newcamd:/xxxxxxxxxxx@fenfui.dynsite.net:xxxx/xxxx4

    What am I doing wrong? Just made a donation and received a code. Can anybody help?
    My port(USB TO nULL mODEM IS 3)
    I am trying to watch without a dongle on CW600S

  2. #2
    Cat RoCK'' Big
    Join Date
    Dec 2010
    Posts
    12,649

    Default

    This should be 1.nfps.bz and not fenfui.dynsite.net.
    card_server_url_1=newcamd:/xxxxxxxxxxx@fenfui.dynsite.net:xxxx/xxxx4. There should be a : in between the user and the password.
    This file needs to be in the same folder as the client .exe.
    your usb to serial needs a driver installed.
    Did you hit return(enter at the end of the last line and save as?

  3. #3

    Default

    Thanks Rockycat, but I seem to hsve the wrong config file. Could you give me a link to the file that has the IP address in the bottom line. The code I got has an IP address, but the file I am using does not have that part to enter the IPm As youwill notice I am a newbie to IKSm Also, I am using a laptop, can I connect using wireless internet connection?

  4. #4
    Cat RoCK'' Big
    Join Date
    Dec 2010
    Posts
    12,649

    Default

    Open the config file with note pad and change the last line to include the information sent in the email. At the end of that line hit enter then file and save as, do nothing but accept and yes. Remember this file needs to be in the same folder as the .exe. How will you hook to the lap top?

  5. #5

    Default

    Sorry to take so long, actually on thge road. I am using a wreless modem. I did all of what you just said, but the config file I am using does not have a URL in the last line, and I am not sure where to put the URL I got with the code I got from Rocket.

  6. #6
    Cat RoCK'' Big
    Join Date
    Dec 2010
    Posts
    12,649

    Default

    Thai is for you to edit in. Pm me with a cut and paste of the last line and all the info from rocket and I'll fix it for you.
    Last edited by rockycat™; 03-26-2012 at 07:30 PM.

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •